On-Demand FEA for Elastomeric Seals & Mold Cavity Design

Stop iterating. Start optimizing.

SealSIM gives seal designers the cavity, lip geometry, radial load and assembly results they need — without the complexity of general-purpose FEA.

Request Trial Access

7-day free trial · Available Now!

SealSIM: simulation software built for radial lip seals

SealSIM is a cloud-based simulation platform built only for radial lip seals and hub/cassette seals. Upload your seal geometry, run a focused module, and download results for mold design and seal performance. You work in your browser. There is no software to install and no workstation to buy.

Designed for seal and tooling engineers, not FEA specialists
Lip geometry predicted to within microns
Results in minutes, not weeks of physical trials
Pre-set, validated mesh and workflows
Input checks before every run
Outputs you can use directly in design and tooling

Why SealSIM — not a generic FEA tool

General-purpose FEA packages can model anything. That generality is the problem. Every seal simulation requires the same expert decisions — mesh density at the lip, contact definitions, hyperelastic material models, convergence settings. SealSIM makes those decisions once, validates them, and locks them in.

Generic FEA tool
SealSIM
Mesh sizing and element type left to the analyst
Pre-set, validated mesh — nothing to size or tune
Material model must be fitted manually from raw test data
M0 builds the hyperelastic model from your bench data automatically
Contact and boundary conditions require FEA expertise to set correctly
Guided input with checks — the platform tells you what to fix before running
Results need post-processing to extract lip geometry and radial load
Outputs are seal-specific: lip diameter, radial load, cavity drawing, animation
Locks budgets into costly annual seat renewals
Pay per run — no annual licence, no workstation required
Lengthy setup and iteration for every new geometry
Upload geometry, assign groups, run — results in minutes

Modules

M0

Material Calibration

Characterize your compound from bench data. Upload uniaxial tensile curves, Shore A hardness and mold shrinkage measurements. SealSIM builds the hyperelastic material model and adds the compound to your database — ready to use in any module.

M1

Cavity → Final Seal

Predict the molded seal before you cut steel. SealSIM simulates the vulcanization and cooling cycle to predict the seal geometry after it shrinks out of the mold — so you know the final lip diameter before committing to tooling.

M2

Target Optimization

Adjust the cavity and compound to hit a target lip diameter. SealSIM iterates the cavity geometry automatically until the predicted final seal matches your specification.

M3

Final Seal → Cavity

Reverse Engineer! Upload the seal geometry and the rubber compound - SealSIM calculates the cavity dimensions required to produce it!

M4

Seal → Sprung Lip

Find the garter spring specification and the resulting radial load. SealSIM models the spring-loaded lip to predict contact pressure distribution and total radial force on the shaft.

M5

Full Assembly

Simulate the complete installation sequence. Press the seal into the bore, then push the shaft through the lip. SealSIM reports interference, contact stress, and radial load at each stage. Choose either Assembly Simulation or Seated State.

M7

Hub / Cassette Seal

Model unitized cassette seals. Assemble the cassette, then simulate its fit into the bearing housing — capturing the interaction between the outer case, inner race, and sealing lips. Choose either Assembly Simulation or Seated State.

How it works

1

Upload your 2D seal geometry (STEP or DXF). For M5 and M7, also upload the bore, shaft, flinger or bearing parts.

2

Assign the named profile groups in the guided interface.

3

Select a compound from your database, or create a new one with M0.

4

SealSIM checks your profile, labels and inputs, and tells you what to fix.

5

Run the module.

6

Download the results, drawings and animation. The mesh is pre-set and validated. There is nothing to size or tune.

Ready to try SealSIM?

Register your interest now. Selected users receive login details for a 7-day free trial.

Contact Us

Business Hours
Mon–Fri09:00 am – 08:00 pm
SatBy Appointment
SunClosed

Subscribe — Sign up to hear from us about specials, sales, and events.